The Family › Thomas Lewis Latané Temple III › In My Opinion
In My Opinion · Latané Temple
Dolly ways and tally sticks
Thursday, July 1, 1971 · The Free Press, Diboll, Texas · page 14
Part 4 of 8 · Sawmill summers, 1933 and 1934 · ← previous part · next part →
It is just possible that there are some people in the Piney Woods of East Texas who do not know what a dolly way is, maybe even a few young ones in the sawmills themselves. It seems to me that the last ones in Diboll and Pineland went out about fifteen years ago, and that is a long time in many people's lives.
Dolly ways were raised wooden tramways which connected the mill, the yards, the sheds, the planer and the carline, six to ten feet high depending on how the ground lay under them. The decking, laid crossways, was rough planking, three inches thick, usually hardwood because it was worth less even though pine was better. Pine would splinter after a few years but would not break.
They were walkways, of course, but their purpose was to serve as roads over which lumber on special buggies called "dollies" (hence dolly way) was pulled from mill to kilns or drying yards to dry sheds to planer to dress sheds to carline. On the carline, where lumber is and was loaded into boxcars, the tram was level to the car floors. Dollies were pulled in the early days by mules, but when I worked as a boy in Diboll one summer, the only mule on the dolly way was the one Dave O'Neal drove.
By then, 1933, they were pulled by jitneys, which were old Model T Fords adapted for the purpose in the mill shop. Their wheelbase was shortened, the body except for two front seats removed, and a sort of singletree or fifth wheel added to make it a little tractor like the big trucks which pull trailer floats.
Dollies had two wheels right in the middle so they would tilt backward or forward to rest on a foot on each end, both of which would be off the ground when the buggy was level. When a buggy was loaded to move a jitney would back up to it, chain the stack to the singletree and take off to where it was supposed to go, the cast iron dolly wheels beating out a clatter on the tram boards.
There were no rails on the dolly ways and at right angles where two came together there was a hazard of cutting a corner too short. Jitney drivers were skilled and daring, and there is no greater thrill in my memory than when I got to hitch a ride with one. One driver in particular that summer was my special buddy. In these 38 years his name has escaped me. I wish I could remember it. When the jitney was on the way back with no buggy to pull, he would let it out and cut corners so close you would swear you were going over the edge.
I worked the first half of that summer stacking number four lumber about where the truck shipping shed is now. The main thing I remember about the job itself was the splinters in my hands. That was before they started "easing" the edges of dressed lumber, but even if it had not been, that near-junk full of splits and red heart would have been mean.
The last half, I was given a special assignment to tally at night on the hardwood chain. This job was to count the board feet of green lumber as it came out of the sawmill. To do this you use a tally stick familiar to all sawmill people. It has numbers on it which will tell you the feet in a board when you determine by eye its length and thickness and measure with the stick the width. Most real workers will laugh at me when I say this was one of the hardest jobs I ever had.
You hold a tally book with flip-pages in your left hand and the stick and pencil in your right, noting with a dot each count. For me, that took a lot of co-ordination through an eight or ten hour night. In addition, I had to recognize instantly several species of oak, two of gum and occasional sycamore, ash, cherry and walnut. And tally by grade, and species.
But the worst part of it was when the chain would break, as it always did at least once in a night. The lumber would stack up until the chain was fixed and then come over in a cascade. I would chase it all the way down the sorting chain.
Of course, it WAS night, so I escaped the August day heat on the job, but then I had to sleep in the hot daytime, lucky to have an old oscillating fan in my room at the "Library".
All this complaining is really bragging, for I am keenly proud and jealous of this stint in the mill. However, I have often wondered what they did with my count. Looking back on it, it could not have been much more than an approximation, no matter how hard I worked at it. Certainly no big decisions were made relying on its accuracy, or the company would have gone broke for sure.
About this text
This is his own account, as he printed it in 1971. It has not been checked against the records; the pages for the people he names show what the records support. The text was typed from the newspaper page by machine and compared with the page image line by line, keeping his spellings. A dotted underline marks a word the print leaves in doubt. Cite as LT3-19710701-IMO.
As it was printed
The column as it ran, cut from the newspaper page and stacked in reading order.
